There's a garbage bin in my head

Chapter 121 Product Sample Preparation
The time soon came to the end of May. During this period, people from the last recruitment came to Blue Sky Intelligence to report one after another. The factory became more and more lively day by day.

In the past, the boss of Zhongcheng Electric set aside almost half of the area on the top floor of the factory building as a staff dormitory. Luo Jiu went to see it, and it was similar to the school dormitory he used to live in when he was in high school.

There are four canopy beds in one room, two floors above and below.But unlike in the school, there are people sleeping on both floors. In the dormitory of the factory, one floor is used to store things and the other floor is used to make beds.

Naturally, the conditions of such a dormitory couldn't be worse.

So after Luo Jiu took over the factory of Zhongcheng Electric and temporarily planned to start work here, Luo Jiu hired someone to renovate these dormitories.

The new dormitory is planned according to the appearance of a rental apartment. There are one-person and two-person residences, and each room is equipped with an independent bathroom.

At the same time, water heaters, air conditioners, wardrobes, desks, wives, etc. are installed. Although it cannot be compared with hotels and homes, the conditions of the new dormitory are still much better than those of most factories.

However, because of the tight schedule, those who had just arrived stayed in the hotel for a month, and did not move into the hastily renovated dormitory until the end of May.

Because of the rush of time, the decoration engineering team almost started at six o'clock in the morning and worked non-stop until ten o'clock in the evening. It was considered that the dormitory was renovated within a month.

However, seeing the students who had just come out of school looking happy to live in the new dormitory, Luo Jiu felt that the extra 20% of the project money given to the decoration team was worth it.

Because it will be put into use immediately after the decoration, all the boards used to decorate the dormitory are the kind of non-polluting and zero-volatile. Although it cannot be said to be the most expensive, it is not cheap at all.

During the month of renovating the dormitory, the work in the factory did not stop at all. Everyone performed their duties and worked hard to do their own work.

Because of the technical data of the county, the technical drawings of the first batch of smart trash cans came out very quickly. When it was fast, drawings of several parts could be produced in a day.

However, when looking for manufacturers to make samples for these parts, they encountered a lot of trouble.

The shell of the smart trash can was first designed according to the data. Without castrating the basic functions, the standard capacity of this trash can is 32 liters, and the volume of the entire trash can reaches 52 liters.

Calculated in this way, there is a huge space of 20 liters for the parts of the smart trash can except the trash module.

Motors, sensors, integrated circuits, and power modules all take up a lot of space, and in the limited space, try to compress the space for installing these components as much as possible, leaving a larger space to accommodate various garbage Space is what these technicians in the factory need to work hard on.

So even if there is a full set of technical information, after the preliminary technical drawings come out, everyone is still simulating assembly and making constant revisions. It is obviously not something that can be completed in a day or two.

However, the drawings of some components have been finalized for the time being. Whether they can meet the requirements will not be known until the final product is produced.

Therefore, for these confirmed parts, it is necessary to find the manufacturer to make samples first.

After determining the general data of the shell specifications of the smart trash can, the technicians modified several drawings with similar shapes, and simulated the real thing on the computer.

In the end, Luo Jiu chose a design that was closest to the sample given by the system, and decided to make this case first.

In the design of technicians, although the appearance of the smart trash can is similar, there are only two materials used to make the shell, one is a stainless steel shell, and the other is a plastic shell.

Because it is only in the sample preparation stage, and what will be modified in the end has not yet been determined, so I chose a lower-cost plastic shell when proofing.

In the past, Zhongcheng Electric had more than a dozen injection molding machines of different sizes, among which three injection molding machines with the largest specifications could just be used to make the shell of smart trash cans.

Although the appearance looks square and relatively simple, the inside can be described as nine bends and eighteen bends. Dozens of hundreds of large and small parts must be placed in this bucket, and enough space must be left. It can be said that there is no space in the place where garbage is used.

Although there are injection molding machines that can produce shells, it is not enough to have an injection molding machine to make the shell of a smart trash can.

The most important injection mold is not there yet, but now that we have the drawings of the shell, we just need to find a mold maker and make the mold.

Luo Jiu asked Li Zhi that in the past, the injection molds of Zhongcheng Electric were made by the former boss in the coastal area according to the product parameters, and then the molds were delivered to the factory by express, and the masters in the factory installed them. Produce the required plastic parts.

But now because the products are still in the design stage, in a large factory of Blue Sky Smart, except for a few aunts in the cafeteria, an aunt who sweeps the floor, and two old guards, all the others are used as offices. In the workshop, there is a No one.

As for the technicians in the office, it is no problem to ask them to use the computer to draw pictures, but it may be a bit difficult for them to operate the injection molding machine.

The old master who used to maintain several injection molding machines in Zhongcheng Electric had already found a new job, and he had no intention of coming back. Luo Jiu couldn't find any good way at once, so he said to Xie Zhengdong: " First find a mold manufacturer to make the mold first. If no one can be found at that time, the mold manufacturer will send someone to install and debug.

During this period of time, if there are suitable technicians in the production workshop who are not easy to recruit, you can recruit some first, so that when the time comes to use them, there will be none. "

During this period of time, the technical department based on the existing equipment in the factory and the equipment planned to purchase, the parts of the entire smart trash can, accounted for about a quarter of the parts that can be produced in the factory, and they are all related to technology and technology. Equipment requirements are not very high parts.

As for other parts, even if the technical requirements of the drawings are finalized, we can only find a suitable manufacturer and send them out to others for production.

Finally, all the parts are gathered in the blue sky, and then the personnel are organized for the final assembly to make trash cans one by one.

At that time, how to improve the efficiency of assembly and improve the pass rate of the final product is what Lantian Intelligent needs to work on.

(End of this chapter)